ГОСТ 19425-74 Балки двутавровые и швеллеры стальные специальные. Сортамент (с Изменениями N 1, 2), ГОСТ от 17 января 1974 года №19425-74

ГОСТ 19425-74

Группа В22

БАЛКИ ДВУТАВРОВЫЕ И ШВЕЛЛЕРЫ СТАЛЬНЫЕ СПЕЦИАЛЬНЫЕ

Сортамент

Special-purpose steel I-beams and channels. Dimensions

МКС 77.140.70
ОКП 09 2500

Дата введения 1975-01-01

Постановлением Государственного комитета стандартов Совета Министров СССР от 17 января 1974 г. N 149 дата введения установлена 01.01.75

Ограничение срока действия снято по протоколу N 4-93 Межгосударственного совета по стандартизации, метрологии и сертификации (ИУС 4-94)

ВЗАМЕН ГОСТ 5157-53 в части балок двутавровых для подвесных путей

ИЗДАНИЕ (октябрь 2012 г.) с Изменениями N 1, 2, утвержденными в ноябре 1977 г., июне 1985 г. (ИУС 1-78, 10-86)

1. Настоящий стандарт распространяется на горячекатаные двутавровые балки для подвесных путей (М), армировки шахтных стволов (С) и швеллеры для автомобильной промышленности (С).

1а. По точности прокатки профили изготовляют:

– высокой точности – А,

– обычной точности – В.

(Введен дополнительно, Изм. N 2).

2. Форма, размеры балок и швеллеров, площадь поперечного сечения, масса 1 м и справочные величины должны соответствовать указанным на черт.1 и 2 и табл.1.

Черт.1

Примечание. Уклон внутренних граней полок должен быть не более:

– для балок М – 12%;

– для балок С – 16%.

Черт.2

Примечание. Уклон внутренних граней полок должен быть не более 10%.

Таблица 1

Номер про- филя								Площадь попереч- ного сечения, см	Масса 1 м, кг	Справочные величины для осей							, см
	мм									, см	, см	, см	, см	, см	, см	, см
Балки двутавровые
14С	140	80	5,5	9,1		7,5	3,8	21,5	16,9	712	102	5,75	58,4	64,8	16,2	1,74	–
20С	200	100	7,0	11,4		9,0	4,5	35,6	27,9	2370	237	8,16	136	159	31,8	2,11	–
20Са	200	102	9,0	11,4		9,0	4,5	39,6	31,1	2500	250	7,95	146	170	33,3	2,07	–
22С	220	110	7,5	12,3		9,5	4,8	42,1	33,1	3400	310	9,00	178	228	41,5	2,32	–
27С	270	122	8,5	13,7		10,5	5,3	54,5	42,8	6550	485	11,0	279	346	56,7	2,52	–
27Са	270	124	10,5	13,7		10,5	5,3	59,9	47,0	6870	507	10,7	297	366	59,0	2,47	–
36С	360	140	14,0	15,8		12,0	6,0	90,9	71,3	17360	964	13,8	574	618	88,3	2,61	–
18М	180	90	7,0	12,0		9,0	3,5	32,9	25,8	1760	196	7,32	113	130	28,9	1,99	–
24М	240	110	8,2	14,0		10,5	4,0	48,7	38,3	4640	387	9,75	223	276	50,2	2,38	–
З0М	300	130	9,0	15,0		12,0	6,0	64,0	50,2	9500	633	12,2	364	480	73,9	2,74	–
36М	360	130	9,5	16,0		14,0	6,0	73,8	57,9	15340	852	14,4	493	518	79,7	2,65	–
45М	450	150	10,5	18,0		16,0	7,0	98,8	77,6	31900	1420	18,0	821	892	119	3,00	–
Швеллеры
18С	180	68	7,0		10,5	10,5	5,3	25,7	20,2	1272	141	7,04	83,5	98,5	20,1	1,96	1,88
18Са	180	70	9,0		10,5	10,5	5,3	29,3	23,0	1370	152	6,84	91,6	111	21,3	1,95	1,84
20С	200	73	7,0		11,0	11,0	5,5	28,8	22,6	1780	178	7,86	104,7	128	24,2	2,11	2,01
З0С	300	87	9,5		13,5	13,5	6,8	49,6	39,1	6500	433	11,4	259,7	289	44,0	2,41	2,13

Примечания:

1. Площадь поперечного сечения и масса 1 м профиля вычислены по номинальным размерам. При вычислении массы 1 м профиля плотность стали принята равной 7,85 г/см.

2. Радиусы закруглений, указанные на черт.1 и 2, на профилях не определяются и даны для построения калибра.

Условные обозначения к черт.1 и 2 и табл.1:

– высота;

– ширина полки;

– толщина стенки;

– средняя толщина полки;

– радиус внутреннего закругления;

– радиус закругления полки;

– момент инерции;

– момент сопротивления;

– радиус инерции;

– статический момент полусечения;

– расстояние от оси до наружной грани стенки.

3. Предельные отклонения по размерам профилей должны соответствовать указанным в табл.2.

Таблица 2

Размеры, мм

Номер профиля	Предельное отклонение
	по высоте профиля		по ширине полки		по толщине полки
	Точность прокатки
	обычная	высокая	обычная	высокая
14	–	±2,0	±2,0	+1,0 -2,0	-0,06
18	±2,5	–	±2,5	–	Плюсовые отклонения ограничиваются предельными отклонениями по массе
Св.18 до 30	–	±3,0	–	±3,0
36	±3,5	–	±3,5	–
45	±4,0	–	±4,0	–

Примечание. Определение толщины полок профилей проводится по калибрам в валках при их расточке.

4. Уклон наружной грани профилей не должен превышать 0,015 .

По требованию потребителя профили изготовляются с уклоном наружной грани полки не более 0,0125 .

5. Кривизна стенки по высоте сечения профиля не должна превышать 0,15 .

6. Притупление наружных кромок полок профилей до N 24 включительно не должно превышать 0,3 t, свыше N 24 – 3 мм.

7. По требованию потребителя несимметричность фланцев полок балок относительно вертикальной оси не должна превышать 1/2 суммы предельных отклонений по ширине полки.

6, 7. (Измененная редакция, Изм. N 2).

8. В соответствии с заказом балки и швеллеры изготовляются длиной от 4 до 13 м:

– мерной длины;

– кратной мерной длины;

– мерной длины с остатком до 5% массы партии;

– кратной мерной длины с остатком до 5% массы партии;

– немерной длины.

Остатком считаются профили длиной не менее 3 м.

9. По требованию потребителя допускается изготовление профилей ограниченной длины в пределах немерной и длиной свыше 13 м.

(Измененная редакция, Изм. N 2).

10. При изготовлении профилей немерной длины допускается наличие профилей длиной не менее 3 м в количестве не более 5% массы партии.

11. Предельные отклонения по длине профилей мерной и кратной мерной длины не должны превышать:

+40 мм – при длине до 8 м;

+80 мм – при длине св. 8 м.

Предельные отклонения по длине профилей мерной и кратной мерной длины для высокой точности прокатки не должны превышать:

+40 мм – при длине до 8 м;

+5 мм на каждый метр свыше 8 м.

12. Кривизна профилей в вертикальной и горизонтальной плоскостях не должна превышать 0,2% длины.

Кривизна профилей в вертикальной и горизонтальной плоскостях для высокой точности прокатки не должна превышать 0,15% длины для профилей высотой до 360 мм и 0,1% длины – для профилей высотой свыше 360 мм.

10-12. (Измененная редакция, Изм. N 2).

13. На каждом профиле дополнительно к требованиям ГОСТ 7566-94 в части маркировки проката должен быть нанесен номер профиля с индексами М или С (18М, 20Са, 36С и т.д.).

14. Определение размеров проводится на расстоянии не менее 500 мм от торца профиля. Высота балки измеряется по оси , швеллера – в плоскости стенки.

15. Предельные отклонения по массе 1 м профиля не должны превышать плюс 3 – минус 5%. Предельные отклонения проверяются предприятием-изготовителем взвешиванием партии массой 20-60 т от каждых 400-500 т проката или кусков профиля длиной не менее 300 мм, отбираемых при прокатке не реже, чем через каждые 100 прокатанных штанг.

16. Марки стали и технические требования – по ГОСТ 535-2005 и другим действующим стандартам, оговоренным в заказе.

17. (Исключен, Изм. N 2).



Электронный текст документа
подготовлен АО “Кодекс” и сверен по:
официальное издание
Стальной листовой прокат.
Сортамент: Сб. ГОСТов. –
М.: Стандартинформ, 2012

90000 IS-Retail Assortment | SAP Blogs 90001 90002 If your SAP system is configured as IS-Retail and you see such a message in purchase order that is one of the reasons you must configure assortments. 90003 90002 90005 90003 90002 90008 Theory 90009 90003 90002 An assortment determines if a store, a distribution center or a customer can receive certain articles at a certain period of time. The assortment can therefore be used to check purchase orders and sales orders (in standard ECC there is listing procedure that can be used for this purpose).90003 90002 By assigning articles to assortments, you determine which assortments and, therefore, which articles a store can buy and sell which means a site can not buy or sell articles that are not included in any of its assortments. Assortment is managed on user level, which could be site (distribution center, store) or Customer. 90003 90002 A good example of usage of assortment would be a company that has a store chain but with different sizes of shops. That means not same assortment is offered to Customers in supermarket compared to small shop in city center.Similarly shop with sport equipment will offer different range of assortment if store is located at seacoast compared to mountain area. 90003 90002 Assortment consists of assortment module or multiple modules. Articles are assigned to assortment module either automatically or manually depending on type of assortment module used. The outcome of this assignment is creation of time dependent listing conditions (if assortment is valid to create listing conditions). 90003 90002 There are two type of assortments: local and general.90003 90002 Local Assortments: 90003 90002 For local assortment two types are defined. Type A for stores and type B for distribution centers. When user creates a site (in other words, a store or distribution center), the system automatically creates a local assortment and then assigns it to the site. This local assortment is site-specific and can not be assigned to another site. Each site has one local assortment created directly and can only be maintained in limited way in Assortment Processing transaction.90003 90002 General Assortments: 90003 90002 General assortments are type C assortments. They can be assigned to any number of Customers, and every Customer can be assigned several general assortments. If multiple assignments parameter has been set in Customizing, user can also use assortments of this type to assign stores and distribution centers. 90003 90002 Mentioned multiple assignment parameter is one of the most important configuration of assortment in SAP. 90003 90031 90032 Parameter 90008 not set 90009.This is a case of 1: 1 assignment and every site has exactly one local assortment (automatically generated during creation of site) and no other assortment can be assigned to this site. 90035 90032 Parameter 90008 set 90009. In the case of n: m assignment is activated and every site still has a local assortment, but there is no limit to the number of general assortments that can be assigned to this site. 90035 90040 90002 Quite interesting situation could be when we have almost the same assortment offered in most of the shops.Without activation of multiple assignment parameter, article needs to be assigned to every local assignment of each site. This would rather cause lot of extra work. To avoid it there are two option but each of them require set of multiple assignment parameter to on. First option is to create general assortment as then assign it to respective sites (in case if particular article is not offered in the store exclusion assortment module may be assigned). Second option is to user reference site and it’s discussed later on.90003 90002 Following assortment modules are delivered by SAP. 90003 90002 Automatic assignment of articles: 90003 90031 90032 Profile module is created automatically during the article maintenance for each assortment and merchandise category. 90035 90032 Shelf modules is generated during the maintenance of layout modules that are assigned to the assortments. 90035 90032 Promotion module contains the articles that are to be dealt with together in a promotion or a theme. 90035 90040 90002 Manual assignment of articles: 90003 90031 90032 Standard module contains any articles from any merchandise categories.It contains the regular long-term rule assortment and is created manually. 90035 90032 Local module is only valid for one site and is therefore the “local assortment” 90035 90032 Exclusion module to exclude articles from the existing assortment for a certain period of time. 90035 90032 Rack jobber modules are modules for which vendors deliver and present articles in stores themselves. This is related to PRICAT and VMI processing. 90035 90032 Value contracts – you can also use these modules for assortment functions in Sales and Distribution in contracts processing.90035 90040 90002 90003 90002 90008 Example of configuration: 90009 90003 90002 For purpose of this article following merchandise categories have been created for single articles: 90003 90031 90032 ZFC_000 – Merchandise category 1 90031 90032 Articles: 1131, 1132, 1133, 1134 90035 90040 90035 90040 90031 90032 ZFC_001 – Merchandise category 2 90031 90032 Articles: 1105, 1106, 1129, 1130 90035 90040 90035 90040 90031 90032 ZFC_002 – Merchandise category 3 90031 90032 Articles: 1135, 1136, має 1137, 1138 90035 90040 90035 90040 90002 To simplify the example following enterprise structure was introduced 90003 90031 90032 Distribution Center ZFD1 (Distribution chain: ZSh2 / P9, Customer: 400068) listing procedure K1 90035 90032 Shop ZFS1 (Distribution chain: ZSh2 / P8, Customer: 400067) listing procedure 02, 90035 90032 Shop ZFS2 (Distribution chain: ZSh2 / P8, Customer: 400068) listing procedure K1, 90035 90032 Shop ZFS3 (Distribution chain: ZSh2 / P8, Customer: 400069) listing procedure Z4.90035 90040 90002 90008 Site master data configuration 90009 90003 90002 In site master data besides listing procedure we find two more parameters: 90003 90002 90120 90003 90002 Subsequent listing ind. only works with goods movements. This means that if article is not listed in particular shop and master data of it does not exist system will create one day entries in tables like Marc, Mard etc, for this particular site. This is valid only for goods movements not Purchase order creation.Second parameter Listing Basic Rule override SD listing procedure in Sales Orders and deliveries processing. Both of parameters have user exits where default behaviour is programmed and is assigned in SPRO in default settings fro IS-Retail 90003 90002 90125 90003 90002 90003 90002 90008 Listing procedure 90009 90003 90002 For the purpose of this article new listing procedure has been created as a copy of K1. The only change compared to K1 procedure is Assotm.ListPro checked. Beside of that standard procedures like 02 -List all, K1 – No listing, B1 – material grade / assormtn and B2 – classification are used.90003 90002 90136 90003 90002 90003 90002 In Listing procedure very important parameter is Assortm.ListPro. Using it we can steer the system which listing procedure to choose during processing of automatic listing. If for example listing procedure for assortment is 02 – All and in the article master data there is entered procedure K1 – Never. 90003 90031 90032 Case 1: in K1 Assortm.Prio is X -> Material is assigned, because it will use listing procedure from assortment and there is assigned procedure 02 – All.90035 90032 Case 2: in K1 Assortm.Prio is blank -> Material is not assigned because article listing procedure takes precedence over listing procedure from assortment. 90035 90040 90002 Beside of it you can also select which listing procedure to be defaulted (can be changed in each of respective objects) in case of allocation, promotion or layout operations. In processing control you can select which checks are executed and how they are connected in logical operation AND or OR. Rules section clearly indicates which function module is executed.Following logic has been implemented: 90003 90031 90032 Selecting parameter “Listing all” – function module in field Ext Listg.ALL is triggered. In standard assortment_version_list_all for list. proc 02 -All or assortment_version_list_never for list. proc K1 – Never 90035 90032 Sequence M – function module from Exit listg. man. (Standard: assortment_version_M) 90035 90032 Sequence P – function module from Exit listg. man. (Standard: assortment_version_P) 90035 90032 Sequence K – function module from Exit listg.man. (Standard: assortment_version_K) 90035 90032 Sequence L – function module from Exit listg. man. (Standard: assortment_version _L) 90035 90040 90002 SAP delivers a number of listing procedures intended to simplify Customizing, which is otherwise rather complicated. The basic listing procedures are: 90003 90031 90032 Merchandise category / assortment grade check – this listing procedure check if for assortment has merchandise category assigned with corresponds to article merch. categ.This is the simples check but as well the most commonly used. You can always split your merch category by grades. With combination to listing algorithm you can select which grades are included. Listing grade is assigned in assortment with merchandise category and in article master data on listing tab. Additionally in listing procedure definition you assign listing algorithm and if grade should be checked. Small hint is that even if in assortment you assigned category but in listing tab of article it remains blank standard module ASSORTMENT_VERSION_P will accept it.90035 90032 Layout check – This procedure checks whether the article is assigned to a specific layout module and the layout module is assigned to a layout and subsequently to an assortment 90035 90032 Classification listing procedure require that class type 047 is assigned to assortment and characteristics values ​​are entered. Additionally same class needs to be assigned to merchandise category either directly or via characteristic profile. Value of characteristics are maintained in article master data and listing can be executed.In standard function module: ASSORTMENT_VERSION_C, program will allow listing even if values ​​are blank and if maintained value comparison with values ​​assigned to assortment is executed. 90035 90040 90002 Hint: If in assortment creation transaction or in site maintenance you will uncheck listing condition, assortment creation then during automatic listing processing assortment is found, assortment module is created but no articles are assigned. I would say that this option can be used more for simulation purpose.90003 90002 90008 New Assortment type for general assortment 90009 90003 90002 90179 90003 90002 At the moment for this assortment type no layout management is foreseen so all checkboxes are not market. 90003 90002 As said before local assortments are always created automatically when new site is launched. In above case there is a new type of assortment for general purpose and needs to be created manually with transaction WSOA1. 90003 90002 90186 90003 90002 90003 90002 For general assortment selection of listing procedure is important and in case of procedure material.grp / assortment (as in above example) valid merchandise category must be assigned to mdse cat. Tab. 90003 90002 Do not forget that local assortments are always assigned only to the site for which they were generated. Additionally sales org and distribution channel of assortment is equal to one defined in corresponding site. For general assortment even if article is assigned to assortment and listing conditions were generated user always needs to be linked to assortment to be able to fully use it.90003 90002 90195 90003 90002 90003 90002 90008 Manual listing 90009 90003 90002 As described before, there are listing procedure which creates assortment modules and assigns to it articles out of different listing procedures automatically. You can create some modules manually like standard module, assign articles and them use them in assortments. 90003 90002 Module creation (Tcode: WSO1) and article assignment 90003 90002 90208 90003 90002 And assignment module to assortment 90003 90002 90213 90003 90002 90008 Article master data 90009 90003 90002 90220 90003 90002 In article master data you set listing procedures per distribution chain (Sales Org and distribution channel).It is important to remember that 90008 it’s not 90009 site dependent. Whenever we run listing execution system will find all assortments with same distribution chain (required fields in assortment) and execute listing procedure (either set in article master data or in assortment, all depends on Assortm.Prio parameter set in listing procedure in article master data ). In above example system will look for all general assortments where Sales org is ZSh2 and Dchl is P1. Due to listing procedure is set to Z4 where Assortm.ListPr is set to X, system will execute check with listing procedure of each found assortment. 90003 90002 Quite useful functionality in listing tab is to select checkbox local assortments also (these assortments with type A – DC or B – Store). Each site is assigned to distribution chain. Article listing view needs to be created for this distribution chain and listing procedures assigned. To determine listing procedure for local assignment system for article, system will find all assortments type A and B.Based on distribution chain from assortments system will read article listing view with mentioned dist. Chain and in case if dist chain is used for store listing procedure is read from store section and in case when distr. Chain is associated with assortment type DC then listing procedure from DC section is read. In this case my local assortments that need to be found is with S.Org ZSh2 and D.Chan P9 for DC and P8 for stores. Then system takes listing procedure for store: 90003 90002 90229 90003 90002 And for DC (data for S.Org ZSh2 and D.Chan P9) 90003 90002 90234 90003 90002 If you mark the checkbox by the ListSupplySite field, you can also list the supplying sites for all articles which can be procured via a warehouse / distribution center. Unfortunately to make this option working we need to have binding between merchandise group and site via assortment. 90003 90002 90008 Reference site 90009 90003 90002 In case if you have multiple sites with the same assortment there is always an option to create assortment for one of them – kind of template.Later on you only create a reference to it as presented below 90003 90002 90245 90003 90002 In this case site ZFS1 can you all assortments of ZFS3. If ZFS3 offers to broad assortment despite of reference there is option to use exclusion module for ZFS1. 90003 90002 90003 90002 As you can see whole listing of articles is rather not easy topic that has a multiple of options and require number of configuration activities. For purpose I did not discussed layout management as this will be part of other article.90003 .90000 Stalwart 20-Piece Bungee Cord Assortment in Plastic Jar – Walmart.com 90001 “,” tooltipToggleOffText “:” Flip the switch to get 90002 FREE NextDay delivery! 90003 “,” tooltipDuration “:” 5 “,” tempUnavailableMessage “:” Coming back soon! “,” HightlightTwoDayDelivery “:” false “,” locationAlwaysEligible “:” false “,” implicitOptin “:” false “,” highlightTwoDayDelivery “: “false”, “isTwoDayDeliveryTextEnabled”: “true”, “useTestingApi”: “false”, “tempUnavailableTooltipText”: “90002 We’re working hard to get back up & running.90003 90006 90007 Temporarily on hold, due to high demand. 90008 90007 Please keep checking back for availability. 90008 90011 “,” ndCookieExpirationTime “:” 30 “},” typeahead “: {” debounceTime “:” 100 “,” isHighlightTypeahead “:” true “,” shouldApplyBiggerFontSizeAndCursorWithPadding “:” true “,” isBackgroundGreyoutEnabled “:” false “} , “locationApi”: { “locationUrl”: “https://www.walmart.com/account/api/location”}, “oneApp”: { “drop2”: “true”, “hfdrop2”: “true”, “heartingCacheDuration”: “300000”, “hearting”: “false”}, “feedback”: { “showFeedbackSuccessSnackbar”: “true”, “feedbackSnackbarDuration”: “3000”}, “accountFlyout”: { “acflyout”: “a “,” accountUrl “:” // www.walmart.com/account”,”trackOrderUrl”:”//www.walmart.com/account/wmpurchasehistory”},”webWorker”:{“enableGetAll”:”false”,”getAllTtl”:”900000 “}}}, “uiConfig”: { “webappPrefix”: “”, “artifactId”: “header-footer-app”, “applicationVersion”: “20.0.25”, “applicationSha”: “a202acde2a0b79bc35a0aa9c87b1d567ba512954”, “applicationName”: “header-footer “,” node “:” 888374062 “,” cloud “:” prod-az-southcentralus-16 “,” oneOpsEnv “:” prod-a “,” profile “:” PROD “,” basePath “:” / globalnav ” , “origin”: “https://www.walmart.com”, “apiPath”: “/ header-footer / electrode / api”, “loggerUrl”: “/ header-footer / electrode / api / logger”, ” storeFinderApi “: {” storeFinderUrl “:” / store / ajax / preferred-flyout “},” searchTypeAheadApi “: {” searchTypeAheadUrl “:” / search / autocomplete / v1 / “,” enableUpdate “: false},” emailSignupApi “: { “emailSignupUrl”: “/ account / electrode / account / api / subscribe”}, “feedbackApi”: { “fixedFeedbackSubmitUrl”: “/ customer-survey / submit”}, “logging”: { “logInterval” 1000, ” isLoggingAPIEnabled “: true,” isQuimbyLoggingFetchEnabled “: true,” isLoggingFetchEnabled “: true , “IsLoggingCacheStatsEnabled”: true}, “nextDayTooltip”: { “enabled”: false, “toggleOnText”: “NextDay delivery mode on! 90002 Toggle Off to exit 90003 “,” toggleOffText “:” Get your items tomorrow with 90002 FREE NextDay Delivery! 90003 “,” tooltipDuration “: 5},” tempUnavailableInfoTooltip “: {” tooltipText “:” 90002 Why can not I get NextDay delivery? 90003 90006 90007 Saturday delivery may not be available from carriers in your area 90008 90007 Delivery may be delayed due to a holiday or unexpected fulfillment interruption 90008 90011 “},” env “:” production “},” envInfo “: {” APP_SHA ” : “69a7066cba7a7e3726af6102d07d69600db4e657”, “APP_VERSION”: “20.0.25-20200630_153741.a202acde2 “},” expoCookies “: {}} 90002 Enter Location 90003 Enter Zip Code or city, state.Error: Please enter a valid ZIP code or city and state 90002 Update location 90003 90028 90002 Good news – You can still get free 2-day shipping, free pickup, & more. 90003 Continue ShoppingTry another ZIP code 90031 90032 90002 Delivering to 90003 90035 Now-FREE NextDay delivery 90036 90037 Same Every Day Low Prices 90008 90037 Free on $ 35 + eligible orders 90008 90041 No membership fee 90008 90002 You’ll lose NextDay delivery if your cart contains one or more items not labeled ” NextDay eligible “.90003 90045 90002 For example: 90003 90002 NextDay + NextDay = NextDay! 90003 90002 NextDay + 2Day = 2Day on entire order 90003 90002 You will not get NextDay delivery on this order because your cart contains item (s) that are not “NextDay eligible”. If you want NextDay, we can save the other items for later. 90003 90002 Yes-Save my other items for later 90003 90045 90002 For example: 90003 90002 NextDay + NextDay = NextDay! 90003 90002 NextDay + 2Day = 2Day on entire order 90003 90002 Oops-it’s past time for NextDay delivery by tomorrow.90003 90002 Order now & get it. 90003 90002 Order by, and we can deliver your NextDay items by. 90003 90002 You will not get NextDay delivery on this order because your cart contains item (s) that are not “NextDay eligible”. 90003 90002 In your cart, save the other item (s) for later in order to get NextDay delivery. 90003 90045 90002 For example: 90003 90002 NextDay + NextDay = NextDay! 90003 90002 NextDay + 2Day = 2Day on entire order 90003 90002 We moved your item (s) to Saved for Later.90003 Oops! There was a problem with saving your item (s) for later. You can go to cart and save for later there. 90031.